Store
Spraying ATTBLIME onto a lattice part

On your 3D scan target

spray ATTBLIME.

Easy even the first time. Shake the can well and spray ATTBLIME while moving at a steady pace. One more thin pass only where coverage is light. Remember just this, and anyone can create a surface that scans beautifully.

Four steps
are all it takes.

  1. 01

    Test a small area first

    Start by checking the material and finish of your target. If you measure dimensions, factor in the coating thickness too.

  2. 02

    Spray a thin, even coat on the surface you will scan

    Choose the nozzle that fits the shape of your target and keep to each product's spray distance. Keep moving steadily so the coating never piles up in one spot.

  3. 03

    Run a test scan and look for gaps

    If data is missing anywhere, check the coating and your capture conditions before spraying more. If you use reference stickers, apply them after coating.

  4. 04

    Finish the job and record your settings

    Finish according to each product's removal method. Note the product, nozzle, spray distance, and working conditions you used. Your next job will go much faster.

Gloved hand holding a bare metal part up to the light Fine mist reaching a part, turning one side matte white Part with blue striped light projected onto a white coating Open blank notebook and pen next to a bare metal part

Recommended for everyone
who 3D scans.
For everyone

Before you scan,ATTBLIME it!

From small models to car bodies,
size is no object.

Scale-model truck cab on a lime-colored stand
Small model
Blue projected light on the floor of a vehicle cargo bed
Inside a car body

Spray and removal methods
for your product.

Sublimating AB 2 500 ml can
Sublimating cansAB ZERO, AB 2, AB 6. The coating sublimates and disappears over time.
AB P(W)
Wipe-off cansAB P is gray and AB P(W) is white. Both are wiped off after the job.
AB 6G 1 L refill container for filling spray equipment
Refill container for spray equipmentAB 6G is a 1 L refill container. Pour it into spray equipment such as an airbrush and spray.

Change the nozzle,
reach every corner precisely.

Wide surfaces or deep gaps, no problem. On can products, swap the SHC nozzle to get a spray pattern that fits the area you are working on.

Round nozzle
Round nozzle for fine detailsSprays a round pattern on small areas.
Variable swivel nozzle
Variable swivel nozzle for wide surfacesSwitches the spray direction between vertical and horizontal.
Extension nozzle
Extension nozzle for deep areasReaches hard-to-access spots with an extension tube.

SHC is a system that swaps the can's spray head. It is different from AB 6G, which you fill into spray equipment.

Cans for right now.
Equipment for wide areas.

Can products are ready to spray the moment you pick them up. AB 6G is a 1 L refill container you fill into spray equipment. Choose by the size of your job and the equipment you use.

Spraying an engine part
Spraying from a canAB ZERO, AB 2, AB 6, AB P, AB P(W). 500 ml cans.
Airbrush laying a fine spray into a narrow groove on a small part
Spraying with an airbrushRefill products are filled into equipment and sprayed like this.
Spray gun coating a wide panel evenly
Spraying with a spray gunFollow the instructions for your equipment and the product.

Choose a can when

  • You want to spray right away without equipment
  • Your parts range from handheld to desktop size
  • You scan occasionally or take it out on site
See can products

Choose the refill container when

  • You have an airbrush or spray gun
  • You often spray wide surfaces like car bodies
  • You want a fine spray on small areas
See AB 6G

This is how you use AB 6G.

  1. 01

    Pour into your equipment

    Pour what you need into the cup of your airbrush or spray gun. Set up compressed air or power according to the equipment manual.

  2. 02

    Spray thin

    Keep moving steadily without stopping and spray a thin, even coat.

  3. 03

    Scan

    After scanning, check the technical data for how to remove the coating. Close the cap and store any leftover liquid.

This is how we spray
on site.

Here we are, spraying the glass ourselves before scanning a vehicle. Even see-through glass is ready to scan once you spray it thinly.

Watch real on-site work
on video.

Spraying from a can

Spraying with equipment

From spray distance to storage,
everything you need is here.